Free Plans Online logo
  FREE PLANS MENU

  MAILING LIST

Join our mailing list and get notified whenever we add new plans.


First Name:

Email Address:

Is poodle a dog or cat?



 
  HOW TO

Dog House Plans

full plans - print version

WESTERN STYLE DOG HOUSE PLANS - INSTRUCTIONS


dog house 2

Materials

1 - 32" x 48" 1/2" plywood (floor)
2 - 16-1/2" x 48" 1/2 plywood (roof)
2 - 13" x 45" 1/2" rigid foam (inside roof)
1 - 39-1/2" x 32" 7/16" masonite siding (front wall)
2 - 31-1/2" x 48" 7/16" masonite siding (sides)
1 - 37-1/2" x 32" 7/16" masonite siding (back wall)
1 - 18" 1/2" quarter round
32" 1-1/2" metal flashing
1 bundle 3-tab shingles
15# felt (enough to cover the roof - 11 square feet)
36" 2x6 (front wall caps and uprights)
49' 2x2 (framing)
47' 1x2 (trim)
2 - 35-1/2" 1x3
exterior paint
29-1/2" x 46-1/2" outdoor carpet (dog house floor)
16d box nails
6d galvanized nails (siding)
6d finishing nails (trim)
1" finishing nails (quarter round)
1" roof nails (to install shingles)
staple gun and 1/4" staples (to install roof felt)
non-toxic adhesive suitable for gluing rigid foam to plywood
exterior Carpenter's glue (optional)


Instructions

NOTE: Although it hasn't been included in the instructions, you can glue any and all lumber together with exterior glue to give it added strength. Just make sure you dry fit the pieces before you permanently glue and nail them together.

Cut and assemble the frame for the floor (Fig. 1). Attach the plywood to the frame.
Cut and assemble the frame for the sides (Fig. 2), front wall (Figs. 3, 3a), and back wall (Fig. 4).

Attach the side, front, and back wall frames to the floor and to once another at each corner.

Position the ridgepole and secure in place by nailing from the outside, through the front and back wall frame, and then into the ends of the ridgepole.

Next, install the rigid foam (which provides insulation and prevents roofing nails from penetrating the interior of the dog house). Start by fitting the roof pieces onto the top of the wall framing.

From underneath, draw a line all the way around where the frame meets the roof plywood. This will give you the area where you will fit and glue the rigid foam.

Lay the roof plywood flat with the inside facing up. Using a utility knife, trim the 2 rigid foam pieces to fit between the lines you drew on each piece of plywood.

Glue the foam in place. Once the glue has set up, you can permanently nail the roof pieces in place.

Install metal roof flashing where the roof meets the back of the front wall (Fig. 5).

Install siding on all four walls. Install siding on the back of the front wall so that it overlaps the metal flashing and fits snug against the roof (Fig. 3c).

Install all the 1x2 and 1x3 trim pieces (Fig. 6). On the 1x2 top trim, "D", on both side walls, you'll need to put a 15 degree bevel to match the roof pitch (see Fig. 6).

Install the 2x6 caps, "A", "B", and "C", on the front wall (Fig. 6).

Nail the 1/2" quarter round in the gap created by the front edge of the plywood floor and the trim across the bottom of the door opening.

Working horizontally, staple felt onto the entire surface of the roof. Make certain you allow it to overlap the ridgeline (don't trim it off flush at the top.

Referring to Fig. 7, install the shingles. (Use a chalk line to keep your rows straight.) To cap off the ridgeline, cut the shingles and install them as shown in Fig. 7a.

Paint siding and trim.

dog house plans 2 figure 1


dog house plans 2 figure 2

dog house plans 2 figure 3

dog house plans 2 figure 3a

dog house plans 2 figure 3b

dog house plans 2 figure 3c

dog house plans 2 figure 4

dog house plans 2 figure 5

dog house plans 2 figure 6

dog house plans 2 figure 7

dog house plans 2 figure 7a



  ADVERTISEMENTS



A Sites500 Website